Typhoon HIL Software Manual
- Introduction
  Overview of the categories covered in the Typhoon HIL Software Manual
- System Requirements
  Guidelines for the hardware and/or software environment necessary to run Typhoon HIL Control Center, for both PC and Test Server/Virtual Machine-based setups.
- Typhoon HIL Quick Start Guide
- Typhoon HIL Toolboxes
  List of the Toolbox Packages available in the Typhoon HIL software suite
  - Basic Schematic Editor libraries
    Description of the basic libraries available in Schematic Editor
  - Modbus Protocol Toolbox
    Schematic Editor components available through the Modbus Protocol Toolbox
  - IEC61850 Protocols Toolbox
    Background on the Schematic Editor components available through the IEC61850 Protocols Toolbox
  - C37.118 Protocol Toolbox
    Schematic Editor components available through the C37.118 Protocol Toolbox
  - Ethernet Variable Exchange Toolbox
    Background on Schematic Editor components available through the Ethernet Variable Exchange Toolbox
  - SFP Simulation Link Toolbox
    Background on Schematic Editor components available through the SFP Simulation Link Toolbox
  - CAN bus Toolbox
    Schematic Editor components available through the CAN bus Toolbox
  - DNP3 Protocol Toolbox
    Schematic Editor components available through the DNP3 Protocol Toolbox
  - EtherCAT Protocol Toolbox
    Schematic Editor components available through the EtherCAT Protocol Toolbox
  - PROFINET Protocol Toolbox
    Schematic Editor components available through the PROFINET Protocol Toolbox
  - IEC 60870 Protocol Toolbox
    Schematic Editor components available through the IEC 60870 Protocol Toolbox
  - ISO 15118 Protocol Toolbox
    Schematic Editor components available through the ISO 15118 Protocol Toolbox
  - Power Loss Calculation Toolbox
    Schematic Editor functionalities available through the Power Loss Calculation Toolbox
  - Nonlinear Machines Toolbox
    Schematic Editor components available through the Nonlinear Machines Toolbox
  - Microgrid Toolbox
    Schematic Editor components available through the Microgrid Toolbox
  - Power Systems Toolbox
    Schematic Editor components available through the Power Systems Toolbox
- Connecting to your HIL device
  Guidelines on how to connect to a HIL device using either USB or Ethernet ports.
- Device Manager
  Device Manager is used to create, manipulate, and activate HIL device setups.
- Typhoon HIL Control Center
  This section provides a general description of Typhoon HIL Control Center and lists the main software components accessible from it, as well as additional software tools which can be invoked from its interface.
- Example Explorer
  General Description of the Typhoon HIL Control Center Example Explorer.
- Signal Access Management
  This feature allows you to change the visibility of signals in Schematic Editor and HIL SCADA
- Schematic Editor
  Introduction to the Schematic Editor tool in Typhoon HIL Control Center
- Schematic Editor Component Libraries
  Detailed functionality and use of the pre-built Component Libraries in Schematic Editor
- Third-party integrations
  This section provides an overview of the key third party integrations within Typhoon HIL's toolchain.
- HIL SCADA
  Description of the HIL SCADA tool in Typhoon HIL Control Center
- Script Editor
  This section describes Script Editor
- Waveform Generator
  This section describes the waveform generator tool in Typhoon HIL Control Center.
- HIL Firmware Manager
  This section describes HIL Firmware Manager
- Test and Calibration Tool
  Description of the Test and Calibration tool in Typhoon HIL Control Center
- TyphoonTest IDE
  This section describes TyphoonTest IDE
- Signal Analyzer
  This section describes the Signal Analyzer tool.
- Lookup table extraction tool
  Description of the Typhoon HIL Control Center tool for extracting characteristics (lookup tables) from datasheet graphs and charts into a format that can be imported by non-linear models.
- Package Manager
  Description of the Typhoon HIL Control Center tool for creating and managing Typhoon packages that contain Schematic examples, Schematic and widget libraries, documentation etc.
- Usage Logging
  This section briefly describes Typhoon HIL software logging feature.
- Python Interpreters
  Overview of how you can use Typhoon HIL Python Interpreters to further customize your test files.

Power Loss Calculation Toolbox

Schematic Editor functionalities available through the Power Loss Calculation Toolbox

The Power Loss Calculation Toolbox is an additional toolbox that enables seminconductor power loss calculation. It implements functionalities within a variety of converter blocks that ensure that both switching and conduction losses are calculated. Switching losses are implemented as a function of current, voltage, and temperature and are defined through lookup tables.

For information about other toolboxes, please refer to the Schematic Editor Toolboxes documentation.

Below is the lists of all Schematic Editor components enabled for power loss calculation by unlocking the Power Loss Calculation Toolbox: