Fiber Optic Output Card parametrization

Description of the set of parameters for the Fiber Optic Output Card in the HIL Connect Interface component.

Real-time only: This document is valid only for real-time simulation.

Parameters

Once you select a card, a series of parameters appear that allow you to describe the pins in your setup and how they are connected. When you select that a pin is connected you will be able to check if you want to Use signal chooser to select a signal from the model that you want to send to the output of that pin. When this is checked as True, the Signal property will appear where you can select the appropriate signal reference. The Invert property will appear next to the Signal property. Check this if the digital signal should be inverted.

Table 1 lists possible parameters for connector X1. The first letter of the property "Name" differs depending on the Slot where the card is located. It can be derived by replacing s with: A, B, C, D, E, F, G, H.

Table 1. Description of X1 Connector parameters
Parameter Name Description
X1 sX01 Check if the X1 connector is used on Slot s on the HIL Connect
X1-1 sX01_1 Select if pin 1 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_1_choose_signal Select if you want to use signal chooser for pin 1 of the X1 connector on Slot s.
Signal sX01_1_selected_signal Choose Signal which should be sent to output pin 1 of the X1 connector on Slot s.
Invert sX01_1_signal_invert Select if you want to invert the assigned signal.
X1-2 sX01_2 Select if pin 2 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_2_choose_signal Select if you want to use signal chooser for pin 2 of the X1 connector on Slot s.
Signal sX01_2_selected_signal Choose Signal which should be sent to output pin 2 of the X1 connector on Slot s.
Invert sX01_2_signal_invert Select if you want to invert the assigned signal.
X1-3 sX01_3 Select if pin 3 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_3_choose_signal Select if you want to use signal chooser for pin 3 of the X1 connector on Slot s.
Signal sX01_3_selected_signal Choose Signal which should be sent to output pin 3 of the X1 connector on Slot s.
Invert sX01_3_signal_invert Select if you want to invert the assigned signal.
X1-4 sX01_4 Select if pin 4 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_4_choose_signal Select if you want to use signal chooser for pin 4 of the X1 connector on Slot s.
Signal sX01_4_selected_signal Choose Signal which should be sent to output pin 4 of the X1 connector on Slot s.
Invert sX01_4_signal_invert Select if you want to invert the assigned signal.
X1-5 sX01_5 Select if pin 5 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_5_choose_signal Select if you want to use signal chooser for pin 5 of the X1 connector on Slot s.
Signal sX01_5_selected_signal Choose Signal which should be sent to output pin 5 of the X1 connector on Slot s.
Invert sX01_5_signal_invert Select if you want to invert the assigned signal.
X1-6 sX01_6 Select if pin 6 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_6_choose_signal Select if you want to use signal chooser for pin 6 of the X1 connector on Slot s.
Signal sX01_6_selected_signal Choose Signal which should be sent to output pin 6 of the X1 connector on Slot s.
Invert sX01_6_signal_invert Select if you want to invert the assigned signal.
X1-7 sX01_7 Select if pin 7 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_7_choose_signal Select if you want to use signal chooser for pin 7 of the X1 connector on Slot s.
Signal sX01_7_selected_signal Choose Signal which should be sent to output pin 7 of the X1 connector on Slot s.
Invert sX01_7_signal_invert Select if you want to invert the assigned signal.
X1-8 sX01_8 Select if pin 8 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_8_choose_signal Select if you want to use signal chooser for pin 8 of the X1 connector on Slot s.
Signal sX01_8_selected_signal Choose Signal which should be sent to output pin 8 of the X1 connector on Slot s.
Invert sX01_8_signal_invert Select if you want to invert the assigned signal.
X1-9 sX01_9 Select if pin 9 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_9_choose_signal Select if you want to use signal chooser for pin 9 of the X1 connector on Slot s.
Signal sX01_9_selected_signal Choose Signal which should be sent to output pin 9 of the X1 connector on Slot s.
Invert sX01_9_signal_invert Select if you want to invert the assigned signal.
X1-10 sX01_10 Select if pin 10 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_10_choose_signal Select if you want to use signal chooser for pin 10 of the X1 connector on Slot s.
Signal sX01_10_selected_signal Choose Signal which should be sent to output pin 10 of the X1 connector on Slot s.
Invert sX01_10_signal_invert Select if you want to invert the assigned signal.
X1-11 sX01_11 Select if pin 11 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_11_choose_signal Select if you want to use signal chooser for pin 11 of the X1 connector on Slot s.
Signal sX01_11_selected_signal Choose Signal which should be sent to output pin 11 of the X1 connector on Slot s.
Invert sX01_11_signal_invert Select if you want to invert the assigned signal.
X1-12 sX01_12 Select if pin 12 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_12_choose_signal Select if you want to use signal chooser for pin 12 of the X1 connector on Slot s.
Signal sX01_12_selected_signal Choose Signal which should be sent to output pin 12 of the X1 connector on Slot s.
Invert sX01_12_signal_invert Select if you want to invert the assigned signal.
X1-13 sX01_13 Select if pin 13 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_13_choose_signal Select if you want to use signal chooser for pin 13 of the X1 connector on Slot s.
Signal sX01_13_selected_signal Choose Signal which should be sent to output pin 13 of the X1 connector on Slot s.
Invert sX01_13_signal_invert Select if you want to invert the assigned signal.
X1-14 sX01_14 Select if pin 14 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_14_choose_signal Select if you want to use signal chooser for pin 14 of the X1 connector on Slot s.
Signal sX01_14_selected_signal Choose Signal which should be sent to output pin 14 of the X1 connector on Slot s.
Invert sX01_14_signal_invert Select if you want to invert the assigned signal.
X1-15 sX01_15 Select if pin 15 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_15_choose_signal Select if you want to use signal chooser for pin 15 of the X1 connector on Slot s.
Signal sX01_15_selected_signal Choose Signal which should be sent to output pin 15 of the X1 connector on Slot s.
Invert sX01_15_signal_invert Select if you want to invert the assigned signal.
X1-16 sX01_16 Select if pin 16 of the X1 connector on Slot s is connected or not.
Use Signal Chooser sX01_16_choose_signal Select if you want to use signal chooser for pin 16 of the X1 connector on Slot s.
Signal sX01_16_selected_signal Choose Signal which should be sent to output pin 16 of the X1 connector on Slot s.
Invert sX01_16_signal_invert Select if you want to invert the assigned signal.

Ports

Desired output signals can be sent to the HIL Connect through the following input port of the HIL Connect Interface component (again, the first letter depends on the Slot where this card is located):

  • sX1

A vector of length 16 should be sent to each input port, where each element of that vector corresponds to one pin of the connector. For example if you want to send a signal to pin 2, you should make sure that that signal is the second element of your vector. If there is a need for inverting signals, inverting them should be done before feeding them to the input terminal.

If signal chooser is used to send measurements to the appropriate output, you should send zero to the input terminal for that pin.